2nd International Conference on Industrial Applications of Adhesives 2022 : Selected Contributions of IAA 2022

translation, reprinting, reuse of illustrations, recitation, broadcasting, reproduction on microfilms or in any other physical way, and transmission or information storage and retrieval, electronic adaptation, computer software, or by similar or dissimilar methodology now known or hereafter developed. The use of general descriptive names, registered names, trademarks, service marks, etc. in this publication does not imply, even in the absence of a specific statement, that such names are exempt from the relevant protective laws and regulations and therefore free for general use. The publisher, the authors, and the editors are safe to assume that the advice and information in this book are believed to be true and accurate at the date of publication. Neither the publisher nor the authors or the editors give a warranty, expressed or implied, with respect to the material contained herein or for any errors or omissions that may have been made. The publisher remains neutral with regard to jurisdictional claims in published maps and institutional affiliations. Preface Contents A Method to Evaluate the Interfacial Adhesion Between Polymer and Metal 1 Introduction 2 Materials and Methods 2.1 Differential Tightness and Permeation Measurement (DTPM) 2.2 Test Specimen Geometry 2.3 Metals 2.4 Polymers 2.5 Specimen Production 2.6 Thermal Post-Treatment 2.7 Tracer Gas Measurement (TGM) 2.8 Light Microscopy (LM) and Scanning Electron Beam Microscopy (SEM) 3 Results and Discussion 3.1 Tightness Validation of PMHs by TGM Method 3.2 Tightness Validation of PMHs by Optical Methods 3.3 Determination of Interfacial Gas Volume Rate of PMHs Using DTPM 3.4 Quantification of Interfacial Adhesion by DTPM Method for Different PMHs 4 Conclusions References Development and Characterization of Silicone Pressure-Sensitive Adhesives Modified Sepiolite for Self-Adhesive Tape Applications 1 Introduction 2 Materials and Methods 2.1 Materials 2.2 Modification of Sepiolite 2.3 Preparation of One-Side Tapes by Using Silicone Pressure-Sensitive Adhesives 2.4 Methods 3 Characteristic of Fillers 4 Results and Discussion 5 Conclusions References Influence of Zeolite on the Silicone Pressure-Sensitive Adhesives Properties 1 Introduction 2 Materials 3 Methods 4 Results and Discussion 5 Conclusion References Optimization of Plasma-Assisted Surface Treatment for Adhesive Bonding via Artificial Intelligence 1 Introduction 2 Materials and Methods 2.1 Materials 2.2 Adhesive Bonding Process 2.3 Testing 2.4 Cost Model 2.5 Bayesian Optimization 2.6 Optimization Settings 3 Results 3.1 Benchmark 3.2 Optimization 3.3 Ageing Tests 4 Conclusion References Mechanical Performance and Economic Analysis of the Addition of Granite Powder and Fly Ash on the Subsurface Properties of Cementitious Floors Cured Under Different Conditions 1 Introduction 2 Materials and Methods 2.1 Ingredients Analysis 2.2 Preparation of Cementitious Overlays 2.3 Schmidt Hammer Compressive Strength Test 2.4 Pull-Off Test of the Subsurface Layer 3 Results 3.1 Schmidt Hammer Compressive Strength Test 3.2 Pull-Off Test of the Subsurface Layer 4 Economic Analysis of the Potential Use of Granite Powder Versus Fly Ash for the Production of Cement Mortars Cured Under Air-Dry and Air-Humid Conditions 4.1 Economic Analysis of the Cementitious Composites 4.2 Analysis of the Mechanical Performance Ratio of the Cementitious Mortars 4.3 Combined Economic and Mechanical Performance of the Composites 5 Conclusions References Mechanical and Cost Analysis of the Effect of the Addition of Granite Powder Waste on Selected Properties of Cement-Lime Plasters 1 Introduction 2 Materials and Methods 2.1 Analysis of the Used Ingredients 2.2 Composition of Used Research Series and Samples Preparing 2.3 Properties of Fresh Cement-Lime Mortars 2.4 Properties of Hardened Cement-Lime Mortars 3 Results and Analysis 3.1 Properties of Fresh Cement-Lime Mortars 3.2 Mechanical Properties of Hardened Cement-Lime Mortars 3.3 Adhesion of Hardened Cement-Lime Mortars 3.4 Influence of Mortar Consistency on Pull-Off Strength Values Concerning the Substrate 4 Cost-Economic Analysis 4.1 Analysis of the Mechanical Properties of a Composite Plaster Mortar 5 Economic Analysis of Composite Plaster Mortar 5.1 Combined Economic and Mechanical Performance of the Composites 6 Conclusions 7 Funding Source References Evaluating the Influence of Short Fiber Reinforced Thermoplastic Composites Produced by Injection Molding on the Stress Distribution in an Adhesively Bonded Joint Using a Multi-Scale Numerical Modeling Approach 1 Introduction 2 Materials and Methodology 2.1 Substrate Material: Short Glass Fiber Reinforced Polymer (SGFRP) 2.2 Adhesive 2.3 Setup Numerical Model 2.4 Step 1: Mori–Tanaka Generalized Homogenization 2.5 Step 2: Eshelby Strain Tensor 2.6 Step 3: Fiber Orientation Tensor 3 Results 3.1 Material Properties SGFRP 3.2 Analytical Stiffness Prediction SGFRP 3.3 FEA Results 3.4 The Effect of the Fiber Volume Fraction 3.5 The Effect of Fiber Orientation 3.6 Global Transverse Isotropy Versus Multi-Scale Modeling 3.7 Effect Joint Design 4 Conclusions References Investigation of Mechanical Properties of Woven Hybrid Metallic Fabric 1 Introduction 2 Materials and Method 2.1 Preparation of Woven Hybrid Metallic Fabrics 2.2 Preparation of Hybrid Laminated Composites 2.3 Tensile Testing of the Hybrid Laminated Composites 3 Results and Discussion 4 Conclusion References Hyperelastic Behaviour of Adhesives and Its Effect on Bonded Joints: An Exploratory Study 1 Introduction 1.1 Hyperelastic Behaviour of the Adhesives 1.2 Elastic-Plastic Properties of the Adhesives and Substrates 2 Joint Configurations and Methods 3 Results and Discussion 4 Conclusions References This book provides selected papers presented at the 2nd International Conference on Industrial Applications of Adhesives 2022, held in Carvoeiro, Portugal, 3-4 March 2022. The volume focuses on applications of adhesive bonding in the industry such as automotive, aeronautic, railway, marine, energy, and electronics. A wide range of topics like adhesion assessment between polymers and metals, pressure sensitive adhesives, adhesive bonding process optimization, civil applications, adhesive joints in composite materials and elastic adhesives are covered. The book presents the latest results and innovations in this field, useful for adhesive producers and adhesive users.